Cationic Polyacrylamide Polymer for Filter Press Equipments
Product Description
Cationic Polyacrylamide polymer for filter press.
Cationic polyacrylamide is a kind of high molecular polymeric electrolyte with water-solubility. It has active groups with rather strong positive charge and an effective function of floe collation. It is easily soluble in water and not soluble in some organic solvent like ethanol and acetone. And it is innocuous, colorless, flavorless and easy to absorb damp.
Advantages:
Economical to use- Effective at very low dosage levels, resulting in reduced handling and storage cost.
Gravity settling operations attain faster settling of sludge solids and improved supernatant clarity.
Belt Press benefits through increased filtration rates and drier sludge cakes. Sludge contains less ash when incinerated.
Centrifuges produce drier sludge cakes, greater throughput, increased solids recovery and clearer centrates.
Air flotation systems produce clearer underflows, greater throughput and increased float-cake solids.
Where sand drying beds are employed for sludge dewatering greater bed ladings and faster drying rates are often possible.
Non-corrosive.
Pricipal uses:
Improves solid-liquid separations in the following applications:
Belt Press of municipal and industrial wastewater sludges and wood pulp suspension.
Gravity, air flotation or centrifuge thickening of wastewater sludges food wastes and paper fines.
Preparation for Application:
This flocculant should be dissolved in water under low agitation to make a 0.01 to 0.05 percent solution. Dissolution should be complete in 60 minutes, but will be faster in warm water. However, avoid temperatures above 500° C. For best results provide further dilution with clean water prior to being fed to the process stream. Avoid turbulent mixing conditions in the process stream after any grade of our cationic flocculants has been added.
Treatment Levels:
For use as:
Belt press, Screw Press, Filter Press or Centrifuge dewatering of municipal or industrial wastewater sludge. 0.1 to 1%/dry solid.
Air flotation of activated sludge or paper mill fines0.1 to 5 ppm
Thickening, clarification or treatment of elutriated, digested primary and waste activated sludge. 0.1 to 5 ppm
Typical properties:
Chemical composition Cationic Polyacrylamide
Appearance: White Granule
Ionicity: Cationic
Bulk Density ( gr / ml ): 0.8
Effective pH Range: 3 ~ 10
PH of solution ( 250C ): About 4
Handling:
Spilled polymer is very slippery. Spills should be scooped and / or wiped prier to flushing with water. Being highly hygroscopic avoid from exposure to air.
Cationic polyacrylamide is a kind of high molecular polymeric electrolyte with water-solubility. It has active groups with rather strong positive charge and an effective function of floe collation. It is easily soluble in water and not soluble in some organic solvent like ethanol and acetone. And it is innocuous, colorless, flavorless and easy to absorb damp.
Advantages:
Economical to use- Effective at very low dosage levels, resulting in reduced handling and storage cost.
Gravity settling operations attain faster settling of sludge solids and improved supernatant clarity.
Belt Press benefits through increased filtration rates and drier sludge cakes. Sludge contains less ash when incinerated.
Centrifuges produce drier sludge cakes, greater throughput, increased solids recovery and clearer centrates.
Air flotation systems produce clearer underflows, greater throughput and increased float-cake solids.
Where sand drying beds are employed for sludge dewatering greater bed ladings and faster drying rates are often possible.
Non-corrosive.
Pricipal uses:
Improves solid-liquid separations in the following applications:
Belt Press of municipal and industrial wastewater sludges and wood pulp suspension.
Gravity, air flotation or centrifuge thickening of wastewater sludges food wastes and paper fines.
Preparation for Application:
This flocculant should be dissolved in water under low agitation to make a 0.01 to 0.05 percent solution. Dissolution should be complete in 60 minutes, but will be faster in warm water. However, avoid temperatures above 500° C. For best results provide further dilution with clean water prior to being fed to the process stream. Avoid turbulent mixing conditions in the process stream after any grade of our cationic flocculants has been added.
Treatment Levels:
For use as:
Belt press, Screw Press, Filter Press or Centrifuge dewatering of municipal or industrial wastewater sludge. 0.1 to 1%/dry solid.
Air flotation of activated sludge or paper mill fines0.1 to 5 ppm
Thickening, clarification or treatment of elutriated, digested primary and waste activated sludge. 0.1 to 5 ppm
Typical properties:
Chemical composition Cationic Polyacrylamide
Appearance: White Granule
Ionicity: Cationic
Bulk Density ( gr / ml ): 0.8
Effective pH Range: 3 ~ 10
PH of solution ( 250C ): About 4
Handling:
Spilled polymer is very slippery. Spills should be scooped and / or wiped prier to flushing with water. Being highly hygroscopic avoid from exposure to air.
| Items | Facade | Molecular | Solid content (%) | Cationic Charge | Solution Time (min) |
| Indexs | Granule | Low-High | ≥88 | Low-High | 60 |
Product Categories : Polyacrylamide / Polyelectrolyte / PHPA
Other Products
Hot Products
Paint fog flocculant Coagulant for for spray booth remove paintACH Liquid Aluminium Hydroxychloride 50%Deodorizing Agents to remove smell Chemical Auxiliary Agent n1Rubber product wastewater treatment rubber deodorant odor controlFood grade aluminium ammonium sulfate/ammonia alum/ammonium alumHigh Quality Poly dadmac Water TreatmentFormaldehyde free fixing agent Excellent stabilityDEODORIZING AGENT to remove bad smell BacteriaCleanwater CW-05 High Quality Water Decoloring Agent For Thailand Dyeing IndustryOrganic Coagulant PolyDADMAC for Effluent TreatmentDecolor Agentwater treatment chemicals polymer polyamineNew Price Effluent Decolorant ChemicalsPAC Polyaluminium Chloride10% Liquid PAC in high purityPolyacrylamide